AEG Cafamosa

Hello,
can someone give me a hint ?
With my Cafamosa CF220 the water runs over the pomace into the collection tray ! I did all the cleaning procedures, nothing helped!
I looked at the inside and noticed that the white plastic part behind where the water comes out is wet so the water doesn't get into the brewing unit at all or ?
Please help me have already had coffee withdrawal symptoms !
Thank you in advance.

Hello,
I have the same problem with my CF 220, was there already a suitable solution?

Thank you

Hello,

also I have the problem with my Cafamosa. The grinding process works normally, but the water runs into the coffee grounds tray at the back instead of the cup at the front. Would be nice if someone knew a problem solution.

Mar7tin

@ Mar7tin

What CaFamosa do you have?

Hello,

>I have to check the exact type designation at home first. However, the device is about 4-5 years old.

Greetings

Mar7tin

OK, at this age, the machine still has Eugster's good technique in it. The upper piston ring of the brewing unit says goodbye. A repair set with instructions is available e.g. at Kuntze

@Hisholy

Thanks for the quick help! I once ordered the repair kit. Hopefully it helps's.

Beauty greetings

Mar7tin

My cafemosa broke after exactly 2.5 years. Same problem as many people have: the water ran in the back. Seems to be a general problem of AEG.the self-repair turns out to be extremely difficult.it didn't work either.
now have a law and I am thrilled!!!!!

Hello,
the solution to your problem is a broken carriage. Check if the white water connection can be pushed back and forth when the brew is removed. It must be fixed because the slide is driven via spindle and motor. Unfortunately the sled often breaks into two parts so that only the front part is pushed back and forth by the engine. the rear part, which sits on the venit of the brueh group, remains standing. therefore the water does not flow into the brueh group but splashes out right behind and lands in the collecting tray, not in the pomace container. If the water lands in the marc, the brueh group is defective. You can get the spare part here: http://www.juraprofi.de/product_info.php?i...r-heinheit.html

Costs 30 Euro. However, you should order the upper cover at the same time, as this plastic cover, which functions as a guide, also often breaks during breakage. The reason for the defect is always an unlubricated/maintained brueh group. When it gets so heavy, the pressure on the car increases and it breaks. The installation is quite extensive, but to be carried out quite well. Open box, remove motor, unscrew upper part of housing and lift off, unscrew spindle guide from below, lift out spindle. Then change the car and reassemble everything. Questions per e-mail to ingohh@gmail.com

Hello everyone,
had the problem that the coffee didn't arrive in the cup! When I opened the machine case I was disappointed about the contents. The coffee runs out of the brewing unit from a hose into an open channel and then into the adjustable cylinder with the two openings from which the coffee then runs into the cup. All open! I am no longer surprised that the coffee never really arrives hot in the cup.
With this run without a lid I immediately saw why the coffee arrived in the marc and not in the cup! The two small openings from which the coffee should run into the cup were clogged! These openings tend to clog after some time despite regular execution of the cleaning program.
In any case, the machine worked perfectly again after cleaning these nozzles. The thorough cleaning of these nozzles is extremely difficult from the outside because these parts are permanently installed on the machine. This is a real design flaw.
I don't want to know what I would have got for a bill if I had sent the machine in for repair. They probably would have dismantled the brewing unit and changed all the sealing rings even though only two holes were blocked.

Greß,
Andreas

hey people also had the problem that no more water came machine made all except for the water.. have them completely disassembled and cleaned everything the mistake was then on the pump the calcified was screwed on it completely disassembled cleaned and reassembled ( ATTENTION ) in the pump is a white ball 1 1.5mm not lose then screwed together works perfectly and if the pump is broken it costs 15 eurons on ebay designation : Ulka Water Pump Model E Type EP5 48Watt
greeting spike