Posted by: Poldi99 March 19, 2017 12:59 pm
Hello
I recently purchased a Siemens EQ6 500
For switching on and rinsing I always place a bowl under the spout. Nevertheless, there is a lot of water in the drip tray where the vault container is. With my old machine, a Delonghi Primadonna, the skin was always dry. Therefore my question to other owners of the same machine: is this normal or a defect?
I have changed to Siemens now after many different Delonghi Primadonna. The reasons were: Siemens is much quieter and the coffee is much hotter. Both has annoyed me with the Delonghis always.
The foam seems to me also more beautiful with the Siemens. Coffee tastes the same to us. Although Siemens needs fewer beans for a coffee mug than the Delonhi
Posted by: Poldi99 March 19, 2017 01:28 pm
Here you can see that the water comes from here.
The machine is about one year old and has about 500 coffees on top.
Posted by: kaffeechris March 19, 2017 03:12 pm
Hello Mr. Poldi, flushes flow in the bowl you have positioned under the coffee spout.
The brewing unit returns to the working position and the water is dropped from the non-return valve to the brewing unit directly into the collecting bowl.
This is what is wanted and has a special name for this system, also for other hestellers, "SingleBrew, for mostley Button".
MfG Chris
Posted by: Poldi99 March 19, 2017 04:58 pm
Thanks!
Then this is so to speak normal?
Posted by: kaffeechris March 19, 2017 06:03 pm
A normal thing 1-2cl can then run into the drip pan.
MfG Chris
Posted by: Poldi99 March 19, 2017 06:11 pm
I just turned it on and off now. There were about 60ccm in the drip tray. So a very big shot glass full. Does that fit?
Posted by: Nicolas February 03, 2019 12:11 am
I also have the EQ.6 in the Plus S100 version and after just switching it on I also have a lot of more than one shot glass in the drip pan. That seems a lot to me...?
Posted by: Fire Dragon February 02, 2020 07:00 pm
I have the same problem, after 5 big cafe crema, I get the hint that the bowl is full. I think that's a bit much. My machine is an eq 6 plus s 100
Posted by: Gast_Anne February 24, 2020 04:27 am
It is the same with me, too. I've had the machine for a week now and it was like this from the beginning. I have the EQ.6 plus I always put a cup underneath and still the drip tray is always full. This can't be normal ]Am very disappointed. I don't know that from my old Saeco:wub:
Posted by: ReGu April 28, 2020 08:24 am
Hello
,also I have the Siemens EQ.6 plus s300 for 14 days now. Also my drip tray is full in certain intervals, despite the drip tray for rinsing when switching on and off. I did not know from my Delonghi either. However, I read somewhere that the brewing unit is also rinsed and this water is led into the drip tray.
Posted by: Gast_Jonas April 28, 2020 06:34 pm
Since three days the EQ.6 Plus s700 extra class in the house and the collection tray is always full
Posted by: Rogier May 28, 2020 12:26 pm
Same here. Siemens EQ.6 s700.
Especially the fact that the coffee dispenser bowl fills with water worries me. In the beginning the coffee dispense was always dry, only containing coffee. Now the sludge is always wet with a layer of water. Is there something leaking, a rubber maybe? Or is this normal?
Posted by: Gast_Eugen June 18, 2020 10:49 pm
QUOTE (Rogier @ Thursday, 28 May 2020, 12:26 pm) |
The same goes for me. Siemens EQ.6 s700. especially the fact that the coffee dispenser bowl fills with water worries me. In the beginning the coffee spout was always dry and contained only coffee. Now the sludge is always wetted with a layer of water. Is there something leaking, maybe a rubber? Or is that normal? </br> |
Posted by: Benjamin Breeg June 19, 2020 07:51 am
QUOTE (Guest_Eyes @ Thursday, 18 June 2020, 22:49 hrs) | ||
I have exactly the same problem. |
Posted by: EQ6plus S700 Tropfschale voll September 14, 2020 12:22 pm
Hello, everyone,
the same problem, drip tray full, water runs out during the brewing process, machine was repaired and even replaced, that should be so right! we have never had this with any other machine before!
Many things are strange about the appliance, additional components in the drip tray so that the hot water does not damage the plastic, various covers that have to be removed for cleaning, the brewing group...really no masterpiece of German engineering
Cleaning the brewing group under running water is not sufficient, mechanical cleaning is necessary, coffee residues everywhere in the corners
Coffee is good, not very good, I had expected more from the high pressure, Coffee purchase very slow
Overall: no recommendation, expensive mistaken purchase
mfg Juergen Reinert
Posted by: Gast_Jörg November 08, 2020 07:50 pm
Hello,
I own the Siemens EQ6 Series 300 and as already mentioned in the forum, our machine underneath it is also wet
Posted by: Gast_David November 09, 2020 01:50 pm
I've just bought an EQ 6 Plus and am AMAZED at how much water goes into the drip tray EVERY SINGLE CUP.
There seems to be a MAJOR DESIGN FLAW with this machine..
Posted by: Gast_Conny December 09, 2020 11:11 am
i have had a Siemens EQ 6 plus s500 for 1 week and i have the same problem with the water, before i had a DeLonghi and there was this problem not. Also the coffee residue is always muddy. A lot of water runs into the drip tray.
Many greetingsConny
Posted by: KStone December 14, 2020 12:43 pm
We bought a reconditioned machine (EQ.6 Extra Class) from a dealer on Friday and are not sure if it is normal for water to drip from the brewing group even though nothing is prepared.
When we pull out the drip tray, it drips mMn very strongly, for the fact that the device is actually not in operation. So I wanted to ask you as "professionals", is this normal? This is actually our first device.
Also, when we pull out the drip tray, we always have some water at the front of the device, which then drips out. Is it the same with you? For a device of this price range I would find that quite unusual
Enclosed you can see photos of the drop inside and the moisture that comes out when the drainer is pulled out.
Thanks for your help!
https://ibb.co/tLCkFZn
https://ibb.co/Z8GNtK3
Posted by: Gast_David January 04, 2021 05:50 pm
I bought our Siemens EQ6 Plus 8 weeks ago and I'm sending it back.
There's a ginormous amount of water always in the 'drip' tray.
We always catch the water at start-up and shut-down in a separate cup.
BUT
After one start-up procedure, 5 cups of coffee, one shut-down procedure there's more than 400cl in the tray ... that's totally RIDICULOUS.
ALSO DESCALING:-
The machine is used for only +/- 5 cups a day on average .. just in use by one person.. but it asks for a descaling procedure every 14-16 DAYS !!!
If it was in use by a family of 4 it would be asking for descaling every 2-3 DAYS ... COMPLETELY RIDICULOUS !!!!!
A disaster purchase..
It's a shame because the coffee is nice .. and hot
Posted by: Gast_Klaus January 29, 2021 02:15 pm
We have the EQ6 now 3 years.
It was 2x in repair without that a change would have occurred.
I've got me the thing now times vorgeknöpft:
Apparently it is probably really normal that during the brewing process a lot of water goes wrong.
Also the pomace is pretty wet. More water ends up in the drip tray than in the cup.
Apparently the seals do not manage to hold the high pressure.
Now the real problem:
The steam in the machine (moisture) causes the coffee to clump together directly at the outlet from the grinder.
You can see this well when you take out the instant coffee container (you can do this by pushing a plastic flag to the side from below with a screwdriver) and draw a coffee.
After the brewing process, it steams out of the chute of the instant coffee container.
More and more coffee misses as a result, clumping up nice and damp in and around the brew group and getting mouldy.
The whole thing is a single, far too complicated faulty construction, with a thousand corners in which coffee powder can stick :-(
In a machine for the price, should not be!!!!!We will
still usethe
machine, leave the powder coffee container outside, so that the steam can out and make the brew group weekly clean.
Then it should work.... Even if it means a lot of work.
After all, the coffee is good and the milk foam dispenser is handy.
It was too expensive to throw away.....
Good luckKlaus
Posted by: Gast_Klaus January 29, 2021 02:16 pm
We have the EQ6 now 3 years.
It was 2x in repair without that a change would have occurred.
I've got me the thing now times vorgeknöpft:
Apparently it is probably really normal that during the brewing process a lot of water goes wrong.
Also the pomace is pretty wet. More water ends up in the drip tray than in the cup.
Apparently the seals do not manage to hold the high pressure.
Now the real problem:
Due to the steam in the machine ( humidity) the coffee clumps directly at the outlet from the grinder.
You can see this well when you take out the instant coffee container (you can do this by pushing a plastic flag to the side from below with a screwdriver) and draw a coffee.
After the brewing process, it steams out of the chute of the instant coffee container.
More and more coffee misses as a result, clumping up nice and damp in and around the brew group and getting mouldy.
The whole thing is a single, far too complicated faulty design, with a thousand corners in which coffee powder can settle :-(
In a machine for the price, should not be!!!!!We will
still usethe
machine, leave the powder coffee container outside, so that the steam can out and make the brew group weekly clean.
Then it should work.... Even if it means a lot of work.
After all, the coffee is good and the milk foam dispenser is handy.
It was too expensive to throw away.....
Good luckKlaus
Posted by: Rene64 March 13, 2021 10:14 am
QUOTE (Guest_Klaus @ Friday, 29 January 2021, 13:15) |
We have the EQ6 now 3 years. It was 2x in repair without that a change would have occurred. I've now had a look at the thing myself: Apparently it's probably really normal for a lot of water to go off during the brewing process. Also the pomace is pretty wet. More water ends up in the drip tray than in the cup. Apparently the seals do not manage to hold the high pressure. Now the real problem: The steam in the machine (moisture) causes the coffee to clump together directly at the outlet from the grinder. You can see this well when you take out the instant coffee container (you can do this by pushing a plastic flag to the side from below with a screwdriver) and draw a coffee. After the brewing process, it steams out of the chute of the instant coffee container. More and more coffee misses as a result, clumping up nice and damp in and around the brew group and getting mouldy. The whole thing is a single, far too complicated faulty design, with a thousand corners in which coffee powder can settle :-( In a machine for the price, should not be!!!!!We will still usethe machine, leave the powder coffee container outside, so that the steam can out and make the brew group weekly clean. Then it should work.... Even if it means a lot of work. After all, the coffee is good and the milk foam dispenser is handy. It was too expensive to throw away..... Good luckKlaus |
Posted by: Conny Rupprecht March 20, 2021 01:16 pm
QUOTE (EQ6plus S700 drip tray full @ Monday, September 14, 2020, 12:22 PM) |
Hello everyone, the same problem, drip tray full, water runs out during the brewing process, machine was repaired and even replaced, that should be so right! We have not had that with any other machine! Many things are strange about the machine, additional component in the drip tray so that the hot water does not damage the plastic, various covers on the brew group that have to be removed for cleaning...really not a masterpiece of German engineering. Cleaning of the brewing group under running water is not sufficient, mechanical cleaning required, coffee residues everywhere in the corners. Coffee is good, not very good, I had expected more from the high pressure, coffee very slowly Overall: no recommendation, expensive bad buy mfg Juergen Reinert |
Posted by: Kaffee_Feinschmecker March 26, 2021 08:37 pm
We have now for 2 years the Siemens EQ6 Plus S700 and have always been satisfied with the machine and the coffee taste. For about 2 weeks it is so that is extremely much water in the drip tray. So far it was actually always so that came in time a message in the display "Empty drip tray". Meanwhile, it is so that we always pay attention to the red mark, so that the bowl does not overflow or is extremely full.
That with the few drops of water on the front, lower side, we can also confirm recently. I bought the maintenance kit for the brew group on Amazon and there renewed all seals and greased - without success. We would also be grateful for a tip on what else it could be. I myself am an electronics engineer and would also trust me to disassemble the machine. For this, however, I should know at which point I have to look approximately.
Posted by: Gast_Axel April 06, 2021 10:07 pm
QUOTE (Coffee_Feinschmecker @ Friday, 26 March 2021, 20:37) |
We have now for 2 years the Siemens EQ6 Plus S700 and were so far always satisfied with the machine and the coffee taste. Since about 2 weeks it is so that is extremely much water in the drip tray. Until now, it was actually always so that a message appeared in time in the display: "Please empty drip tray". Meanwhile, it is so that we always pay attention to the red mark, so that the bowl does not overflow or is extremely full. That with the few drops of water on the front, lower side, we can also confirm recently. I bought the maintenance kit for the brew group on Amazon and there renewed all seals and greased - without success. We would also be grateful for a tip on what else it could be. I myself am an electronics engineer and would also trust me to disassemble the machine. For this, however, I should know at which point I have to look approximately. |
Posted by: Kaffee_Feinschmecker April 14, 2021 08:44 am
Sorry that I get in touch first now. Have not found time before and the spare parts had to be ordered.
I have replaced the ceramic valve. This brought no change. In another repair forum, I have read the advice that one should change the seals (search on Amazon Siemens Eq6 repair / maintenance kit), the coupling for the brewing unit (item number: 00620989) and connection unit / brewing chamber inlet for brewing unit (item number: 00616637).
Photo brewing unithttps://ibb.co/b15wD4b
https://ibb.co/0FRywVs
I also
changedthe
seal / O-ring for the ceramic valve (item number: 00633878).
Please order and change this at the same time as replacing the ceramic valve.
https://ibb.co/N3bKg4W
I have a better crema again and from the seal of the ceramic valve no more water runs on the wall into the drip tray.
Unfortunately, I still have the problem that the drip tray is full very quickly. I noticed yesterday that there is a white opening at the bottom, where the water drips into the bowl for minutes. Does anyone know what the opening is for or how I can stop this?
https://ibb.co/dGjGq7s
Posted by: Gast_Andy May 17, 2021 09:03 pm
Hello all,
we have since a few days also problems with our Siemens EQ 6 700 or so Our machine is now 2-3 years old.
I am satisfied with the design of the machine eigendlich. I prefer to be able to open and clean my machine myself. That's why we chose the Siemens model. So far so good.
But now we have noticed that our machine starts to rinse incorrectly. Since then, a lot of water ends up in the coffee grounds container when the machine is switched on and off. So much water that the Puks there become coffee water.
The coffee preparation is visuel the same.
What the previous speaker has done everything (seals, etc.) I have also done.
The rinse cycle was not better but again a little better taste.
Just noticed that we have since a few days also new coffee in it. I do not understand why the rinsing is therefore worse.
Does anyone have an idea what this can be?
Greetings
Posted by: Africoffee July 03, 2021 10:22 am
Siemens eq. 6 plus s500. 4years old. 4000+ brews. Recently (?6 months) more water in grounds receiving container and pucks reduced to slush!
Any solutions to this problem?
Posted by: Cafe-Monaco January 22, 2022 10:11 am
QUOTE (Coffee_Feinschmecker @ Wednesday, April 14, 2021, 07:44 PM) |
Sorry that I get in touch first now. Did not find time before and the spare parts also had to be ordered. I have replaced the ceramic valve. This brought no change. In another repair forum, I have read the advice that you should change the seals (search Amazon Siemens Eq6 repair / maintenance kit), the coupling for the brewing unit (item number: 00620989) and connection unit / brewing chamber inlet for brewing unit (item number: 00616637). https://ibb.co/b15wD4b https://ibb.co/0FRywVs I still have the seal / O-ring to the ceramic valve (part number: 00633878) changed. Please order and change this at the same time as replacing the ceramic valve. https://ibb.co/N3bKg4W I have again a better crema and from the seal of the ceramic valve runs no more water on the wall in the drip tray. Unfortunately, I still have the problem that the drip tray is full very quickly. I noticed yesterday that there is a white opening at the bottom, where the water drips into the bowl for minutes. Does anyone know what the opening is for or how I get that turned off ? https://ibb.co/dGjGq7s AdminI can post here neither photo links nor normal clickable links. Why ? Can this be unlocked with me to make my post more descriptive ? |
Posted by: Cafe-Monaco January 22, 2022 12:11 pm
Hello everyone
,I also have an EQ.6 plus s700 (TE657509DE) about 3 years old and the similar problem as "Kaffee_Feinschmecker" describes:
Posted by: Mauriceeeee February 13, 2022 03:43 pm
QUOTE (Coffee_Feinschmecker @ Wednesday, April 14, 2021, 07:44 PM) |
Sorry that I get in touch first now. Did not find time before and the spare parts also had to be ordered. I have replaced the ceramic valve. This brought no change. In another repair forum, I have read the advice that you should change the seals (search Amazon Siemens Eq6 repair / maintenance kit), the coupling for the brewing unit (item number: 00620989) and connection unit / brewing chamber inlet for brewing unit (item number: 00616637). https://ibb.co/b15wD4b https://ibb.co/0FRywVs I still have the seal / O-ring to the ceramic valve (part number: 00633878) changed. Please order and change this at the same time as replacing the ceramic valve. https://ibb.co/N3bKg4W I have again a better crema and from the seal of the ceramic valve runs no more water on the wall in the drip tray. Unfortunately, I still have the problem that the drip tray is full very quickly. I noticed yesterday that there is a white opening at the bottom, where the water drips into the bowl for minutes. Does anyone know what the opening is for or how I get that turned off ? https://ibb.co/dGjGq7s AdminI can post here neither photo links nor normal clickable links. Why ? Can this be unlocked with me to make my post more descriptive ? |
Posted by: Mauriceeeee February 13, 2022 03:51 pm
QUOTE (Coffee_Feinschmecker @ Wednesday, April 14, 2021, 07:44 PM) |
Sorry that I get in touch first now. Did not find time before and the spare parts also had to be ordered. I have replaced the ceramic valve. This brought no change. In another repair forum, I have read the advice that you should change the seals (search Amazon Siemens Eq6 repair / maintenance kit), the coupling for the brewing unit (item number: 00620989) and connection unit / brewing chamber inlet for brewing unit (item number: 00616637). https://ibb.co/b15wD4b https://ibb.co/0FRywVs I still have the seal / O-ring to the ceramic valve (part number: 00633878) changed. Please order and change this at the same time as replacing the ceramic valve. https://ibb.co/N3bKg4W I have again a better crema and from the seal of the ceramic valve runs no more water on the wall in the drip tray. Unfortunately, I still have the problem that the drip tray is full very quickly. I noticed yesterday that there is a white opening at the bottom, where the water drips into the bowl for minutes. Does anyone know what the opening is for or how I get that turned off ? https://ibb.co/dGjGq7s AdminI can post here neither photo links nor normal clickable links. Why ? Can this be unlocked with me to make my post more descriptive ? |
Posted by: Guest February 13, 2022 05:36 pm
what is the white part? Pump?
Posted by: Mauriceeeee February 13, 2022 07:01 pm
QUOTE (Guest @ Sunday, 13 February 2022, 16:36) |
what is the white part? Pump? |
Posted by: Gast_Rüdiger February 16, 2022 06:07 pm
QUOTE (Mauriceeeee @ Sunday, February 13, 2022 at 7:01 PM) | ||
Pump I think not, it drips yes even if the machine is switched off the water comes directly from the tank, have already considered whether it can be the water tank coupling. |
Posted by: Mauriceeeee February 17, 2022 09:47 am
QUOTE (Guest_Rüdiger @ Wednesday, February 16, 2022 at 5:07 PM) | ||||
Hello, I have the same problem. Water leaks from the opening to tank lerr. Already an idea |
Posted by: Mave1512 March 06, 2022 04:21 am
Have the same problem with the white drip. Someone of you already found a solution?
Posted by: Gast_Timo March 18, 2022 01:35 pm
I have the EQ6 S500 now for 14 days and have to empty the bowl several times a day.
The KVA turns off but also after 30 min standstill. Will try to set the standby time to 4 hours. If I still have to empty the tray after every cup, I'll throw the machine in the nearest Siemens office.
That's everything but quality.
Posted by: Cafe-Monaco March 19, 2022 02:04 pm
Does anyone have any idea what it may be?
Ceramic valve?
Posted by: Sören March 29, 2022 06:09 pm
QUOTE (KStone @ Monday, December 14, 2020, 12:43 PM) |
We bought a refurbished machine (EQ.6 Extraklasse) from a dealer on Friday and are not sure to what extent it is normal that water drips from the brew group, although nothing is prepared. When we pull out the drip tray, it drips mMn very strongly, for the fact that the device is not actually in operation. Therefore, I wanted to ask you as "professionals" if this is normal? This is actually our first unit. Also, when we pull out the drip tray, we always have some water in the front of the unit that drips out. Is this the same for you guys? For an appliance in this price range, I find this quite unusual Attached you can see photos of the drip inside as well as the moisture that comes out when pulling out the drip tray. Thanks for your help! https://ibb.co/tLCkFZn https://ibb.co/Z8GNtK3 |
Posted by: Mauriceeeee April 05, 2022 10:42 pm
QUOTE (Mave1512 @ Sunday, 06 March 2022, 03:21 PM) |
Have the same problem with the white drip. Any of you guys found a solution yet? |
Posted by: Gast_Stefan April 08, 2022 10:37 am
Now I've read through the whole thread here and that makes me shudder.
Have had the EQ6 700s for three days and after the first day when emptying the drip tray in the evening found that there was a lot of water felt in the drip tray. Also found water in the front under the machine. I thought that something had sloshed over when I removed the bowl and lifted the machine to the side to dry. There was more water than I thought, even in the back left. I still blamed it on my carelessness when pulling out the bowl.
Yesterday (day 2) then the same thing again, although I am very sure that I did not spill any water this time when I pulled it out, as I paid extra attention. Bowl was very full of water and under the machine again very wet.
Machine goes back, replacement is already on the way. And then I read this....
After 20 years of Jura I have dared this change, but should the described here also show up again with the new machine, then it was for me with Siemens.
Let's be surprised!
Posted by: Gast_Stefan April 10, 2022 10:46 am
I have now examined again more closely. Bowl cleaned and dried and left overnight in the machine. The next morning there is water in the bowl. Not much, but still. Exactly under the place described by @mauriceeeee with the outlet of the pump. That is, even with me, the pump lets water through when it is turned off. Before cleaning, the machine had also been off for several hours, so it couldn't be residual water from the last draw.
When I then pulled out the bowl, there was still water underneath
!
In the bowl there is a small hole with a silicone plug or something similar at this point where the water probably also drips from the pump, in my opinion the only place where the water can get out of the bowl.
This of course makes me wonder why there is such an opening in the bowl.
My machine is brand new, now only in operation for 4 days. The pump lets water through when switched off and through an obvious leak in the bowl, the sense of which is not clear to me, the water runs to the outside and from the front under the machine... Clearly that goes back and I also no longer want a replacement for it, after everything I have read here so.
That was my brief, enlightening experience with Siemens...
Posted by: Gast_Jürgen April 18, 2022 09:41 am
QUOTE (Benjamin Breeg @ Friday, June 19, 2020, 07:51 PM) | ||||
Hello all. We have the EQ 6 plus S 300 and the same problem. But I can still live with it. Much worse is that the machine seems to be leaking somewhere. We always have a kitchen towel lying underneath. That sucks then beautifully icky full. Does anyone have an idea or experience with? LG. |
Posted by: Gast_Klaus July 27, 2022 09:57 am
QUOTE (KStone @ Monday, 14 December 2020, 12:43 PM) |
We bought a refurbished machine (EQ.6 Extraklasse) from a dealer on Friday and are not sure to what extent it is normal that water drips from the brew group, although nothing is prepared. When we pull out the drip tray, it drips mMn very strongly, for the fact that the device is not actually in operation. Therefore, I wanted to ask you as "professionals" if this is normal? This is actually our first unit. Also, when we pull out the drip tray, we always have some water in the front of the unit that drips out. Is this the same for you guys? For an appliance in this price range, I find this quite unusual Attached you can see photos of the drip inside as well as the moisture coming out when pulling out the drip tray. Thanks for your help! https://ibb.co/tLCkFZn https://ibb.co/Z8GNtK3 |
Posted by: VitKe January 23, 2023 10:33 am
QUOTE (Mauriceeeee @ Sunday, February 13, 2022, 2:51 PM) | ||
Hello, since yesterday I have the same problem with this white thing where all the time the water drips out, it drips until the tank is empty, please help. |
Posted by: Gast_Steffen March 31, 2023 07:28 am
This is the pulsation damper. It contains a rubber plug and a spring. This rubber plug is worn out or the spring is worn out. https://komtra.de/siemens-ersatzteile/siemens-ersatzteile/pulsationsdaempfer-pumpe-siemens-eq-bosch-vero.html de/siemens-ersatzteile/siemens-ersatzteile/pulsationsdaempfer-pumpe-siemens-eq-bosch-vero.html
Posted by: kaffeechris April 03, 2023 05:30 pm
There is a possibility that one or more factors lead to too much water in the collection container or in the pulp container.
Brewing unit should run smoothly. O-rings regularly (lightly) lubricate with silicone grease. In addition, the brewing unit must be cleaned regularly. USW....
If the manual knowledge or skill it is not sufficient for the disassembly of the KVA's then please to the customer service. Almost every city has a KVA specialist.
Posted by: langedewil@gmail.com April 11, 2023 11:55 am
EQ 9 Plus s500 Siemens leaks a lot of water outside the drip tray.
What to do about this
WBJ
Posted by: Muks June 04, 2023 09:34 pm
QUOTE (EQ6plus S700 Tropfschale voll @ September 14, 2020 12:22 pm) |
Hello, everyone, the same problem, drip tray full, water runs out during the brewing process, machine was repaired and even replaced, that should be so right! we have never had this with any other machine before! Many things are strange about the appliance, additional components in the drip tray so that the hot water does not damage the plastic, various covers that have to be removed for cleaning, the brewing group...really no masterpiece of German engineering Cleaning the brewing group under running water is not sufficient, mechanical cleaning is necessary, coffee residues everywhere in the corners Coffee is good, not very good, I had expected more from the high pressure, Coffee purchase very slow Overall: no recommendation, expensive mistaken purchase mfg Juergen Reinert |
Posted by: Bernt February 28, 2024 06:38 am
QUOTE (Guest_David @ Monday, January 04, 2021, 5:50 pm) |
I bought our Siemens EQ6 Plus 8 weeks ago and am now sending it back. There is always a gigantic amount of water in the "drip tray". We always catch the water in a separate cup when switching on and off. BUT after one start process, 5 cups of coffee, one switch-off process, there are more than 400cl in the bowl ... this is totally DISGUSTING. ALSO DESCALING:-The machine is only used for +/- 5 cups per day on average ... only in use by one person. but it requires a descaling procedure every 14-16 DAYS !!!If it were used by a family of 4, it would require descaling every 2-3 DAYS ... COMPLETELY RIDICULOUS !!!!!A disaster purchase. .</br></br>. It's a shame because the coffee is nice .. and hot</br></br></br></br></br></br></br></br></br></br> |
Bean2cup.org > Siemens > Siemens Eq6 leaking?