Bomann CB2001 Hot water nozzle does not work

If I bought the machine used, everything should be fine.

However, when I got the machine, all lamps flashed for the first time. Then decalcified the machine according to the instructions and see there, instead of out of the nozzle the water runs into the machine.

Coffee makes it perfect. One may only not use the steam or hot water nozzle.

Now I must decalcify again.

Achja the steam comes out in the device somewhere exactly above the nozzle.
The hose may be loose or so.

How do I get there? What can I do?

Thanks already

If the lamps flash, the machine heats up and if water comes out of the machine, the hose, connection or boiler may be leaking. Repair & Maintenance General or Others.Bomann is identical in construction to Clatronic, Medion

Now I screwed on the machine as described here, but here is only described up to the sidewall, that's it, but I still can't reach it. What happens now? Afraid to break something off.

behind the front left and right believe each 2screws to loosen. coffee spout off.2Now carefully front part below pull forward about 45 degrees then press upwards Possibly above with a screwdriver lever upwards, because the parts have round pins at the top like the side parts, but with caution you can but if it does not work, at the top behind the heating plate under the water tank and bean container to loosen the screws Then it goes a little better, I could imagine that something is clogged with my Kav also .was once tense what the boiler makes.

I've got everything open now, can't recognize anything, no hoses, boiler OK, I think, but where the rubber hose from the nozzle is connected to the metal tube inside, where there's another thick rubber hose over it, the threads were easy to turn, now they've got some tightness, well screw together and try.

If the nozzle is clogged, how do I notice that and what do I do?

So I found the mistake, although the loose connection also had something to do with it, because now water and steam are coming out of the nozzle. Only unfortunately not only.
Lot left the side wall open and tried everything.

There is a big silver part looks like a U with connections on each side, there it splashes out in the lower arc. Seems to be a hole. What's the name of that thing? Is it still possible to buy something like this and install it?

That will be the heater instantaneous water heater? Have you dismantled the front part.how did you decalcify when water runs out of the machine.with the right decalcifying I had to decalcify at least 2 times 1 liter with decalcifier and 2 times without decalcifying.sometimes wennder KVA spins even more often.Then it takes 1 hour.to test I have not screwed the KVA together.I think I still have such a part there.

I now decalcified with open side wall above the sink ;-)
most of the water is now coming out of the nozzle (is it normal, that the hot water also splashes out with enormous pressure, so in the jet)
but also from the bottom of the instantaneous water heater

I come from Berlin, would be great if you still have such a part there

Hello!
Please send me an email with Tnr and when can I reach you?

I've registered now.

Super Board, fast and competent help. Can only praise you all

Hi, there. Did you get any e-mail?

Got the instantaneous water heater from a hobbyist. Thanks again.

Part installed, grinder and brewing unit cleaned. Afterwards again decalcified.
And everything runs super! coffee of the finest.

missip

Hello!
Glad I could help you and thank you for the feedback. Not as with most questions and then leave without an answer
I wish good coffee enjoyment hobbyists

hallo

has also problems with the bomann:-(

it barely comes out water vll. 4cl.

enkalkt I have it unfortunately no improvement.

Vapour and hot water works perfectly.

Always when I test and try to make coffee blink refill what can this be?

Where can I find a guide to open?

Thanks in advance