KRUPS EA81* EA8105 EA810507 Reset

Hello and thank you for the post with the reset!

My EA8109 without display got a new drainage valve a few weeks ago, after the reset instructions everything worked again.

Now I have the problem since yesterday that the upper piston stays up. It no longer moves down. Not even with a little "pressure". Am I doing something wrong with the reset, or is the pressure cylinder broken?

If I press down a few mm by hand, the piston returns to its original position at the end of the procedure.

QUOTE (Gast_HaWe @ Saturday, November 28, 2020, 5:22 pm)

KRUPS EA81* Reset with or without cleaning slide. Pomace container and water container LED flashing. Trying to change the grinder setting, grinder grinding time, grinding quantity, coffee powder quantity according to a procedure described in the forums usually makes the machine unusable. The grounds container and water container LEDs flash after restarting, no more button input possible, machine does not heat up. In a forum, an unknown forum user has described a possible RESET for all those affected. I expressly emphasize that I am not the inventor of this procedure, the credit goes to an unknown person. I am merely transferring the procedure into a readable form and adding a few more steps. I have tried it on a machine WITHOUT a cleaning slide. It works! 1. Disconnect the machine from the power supply (unplug) 2. Remove the water tank, grounds container and cleaning slide (if present) 3. Set the flow regulator to 20 ml 4. Press and hold the "strong coffee" button on the far right and plug in 5. All LEDs light up, water tank filled, grounds container, reset cleaning slide (if present) 6. Adjust the flow regulator until all LEDs have gone out (approximately middle position) 7. Place the container under the coffee spout and steam nozzle, now press the "weak coffee" button 8. Water is pumped through the coffee spout and steam nozzle, the brewing piston moves to the upper edge of the brewing chamber. The process is repeated twice. Then all red LEDs have gone out 9. Press the "weak coffee" button again 10. The machine lowers the brewing piston twice, the last time the brewing piston remains in its lowest position. When "all LEDs are flashing" 11. Unplug the machine and wait at least 5 seconds 12. Plug in the mains plug, the brewing piston returns to its original position. Machine is working again.

Krups EA8108 RESET
Worked

QUOTE (Krups EA8108 @ Sunday, June 30, 2024, 20:07)

QUOTE (Guest_HaWe @ Saturday, November 28, 2020, 5:22 pm) KRUPS EA81* Reset with or without cleaning slide. Pomace container and water container LED flashing. Trying to change the grinder setting, grinder grinding time, grinding quantity, coffee powder quantity according to a procedure described in the forums usually makes the machine unusable. The grounds container and water container LEDs flash after restarting, no more button input possible, machine does not heat up. In a forum, an unknown forum user has described a possible RESET for all those affected. I expressly emphasize that I am not the inventor of this procedure, the credit goes to an unknown person. I am merely transferring the procedure into a readable form and adding a few more steps. I have tried it on a machine WITHOUT a cleaning slide. It works! 1. Disconnect the machine from the power supply (unplug) 2. Remove the water tank, grounds container and cleaning slide (if present) 3. Set the flow regulator to 20 ml 4. Press and hold the "strong coffee" button on the far right and plug in 5. All LEDs light up, water tank filled, grounds container, reset cleaning slide (if present) 6. Adjust the flow regulator until all LEDs have gone out (approximately middle position) 7. Place the container under the coffee spout and steam nozzle, now press the "weak coffee" button 8. Water is pumped through the coffee spout and steam nozzle, the brewing piston moves to the upper edge of the brewing chamber. The process is repeated twice. Then all red LEDs have gone out 9. Press the "weak coffee" button again 10. The machine lowers the brewing piston twice, the last time the brewing piston remains in its lowest position. When "all LEDs are flashing" 11. Unplug the machine and wait at least 5 seconds 12. Plug in the mains plug, the brewing piston returns to its original position. Machine is working again. Krups EA8108 RESET Worked

Krups EA8108 RESET
Worked

But, at step 3: set the dial to amount of water NOT to 20ml (minimum), but to 220ml (maximum).
Then, at step 6: turn the dial all the way down to 20ml (minimum), and then back to 220ml (maximum).

If you follow the original instruction, after the reset, the amount of water at the dial of 20ml will be much BIGGER than 20ml.

QUOTE (Krups EA8108 @ Sunday, June 30, 2024, 21:07)

QUOTE (Krups EA8108 @ Sunday, June 30, 2024, 20:07) QUOTE (Guest_HaWe @ Saturday, November 28, 2020, 5:22 pm) KRUPS EA81* Reset with or without cleaning slide. Pomace container and water container LED flashing. Trying to change the grinder setting, grinder grinding time, grinding quantity, coffee powder quantity according to a procedure described in the forums usually makes the machine unusable. The grounds container and water container LEDs flash after restarting, no more button input possible, machine does not heat up. In a forum, an unknown forum user has described a possible RESET for all those affected. I expressly emphasize that I am not the inventor of this procedure, the credit goes to an unknown person. I am merely transferring the procedure into a readable form and adding a few more steps. I have tried it on a machine WITHOUT a cleaning slide. It works! 1. Disconnect the machine from the power supply (unplug) 2. Remove the water tank, grounds container and cleaning slide (if present) 3. Set the flow regulator to 20 ml 4. Press and hold the "strong coffee" button on the far right and plug in 5. All LEDs light up, water tank filled, grounds container, reset cleaning slide (if present) 6. Adjust the flow regulator until all LEDs have gone out (approximately middle position) 7. Place the container under the coffee spout and steam nozzle, now press the "weak coffee" button 8. Water is pumped through the coffee spout and steam nozzle, the brewing piston moves to the upper edge of the brewing chamber. The process is repeated twice. Then all red LEDs have gone out 9. Press the "weak coffee" button again 10. The machine lowers the brewing piston twice, the last time the brewing piston remains in its lowest position. When "all LEDs are flashing" 11. Unplug the machine and wait at least 5 seconds 12. Plug in the mains plug, the brewing piston returns to its original position. Machine works again. Krups EA8108 RESET Worked Krups EA8108 RESET Worked But, at step 3: set the dial to amount of water NOT to 20ml (minimum), but to 220ml (maximum). Then, at step 6: turn the dial all the way down to 20ml (minimum), and then back to 220ml (maximum). If you follow the original instruction, after the reset, the amount of water at the dial of 20ml will be much BIGGER than 20ml.

Actually, in my case, it doesn't matter where I put the dial initially, it always gives me 40ml of coffee at the 20ml setting.
I think, this is because when I fixed the water counter, which has 2 magnets, I have accidently reversed polarity of one of them, and now only 1 magnet is used, thus the double of the volume.
This is still in theory.
I will check it out whenever I'm really pissed about drinking espresso instead of ristretto.

QUOTE (Jeezluis @ February 05, 2024 05:46 pm)

Too everyone with a EA81x WITH DISPLAY with a "missing waste container" bricked machine after trying to follow reset instructions read on: The way to fix this is simple, and yet was impossible to find anywhere. Unplug the machine. Remove water tank and waste container. Press the ⚙ button while plugging it back in the wall socket to enter the service menu. Insert waste container back in. Press start and the should be displayed d69 and the icon to unplug the machine flashing. Unplug the machine again. Insert the water tank and plug the machine back ~ You should now be able to turn on the machine and use it normally.

Thanks
IT WORKS.

Hello, when I switch on my EA8105, a cycle starts immediately in which the piston moves a few times, the pusher wants to push the (non-existent) coffee grounds into the grounds container, but then a flashing LED indicates that the container is full. So I take the (empty) container out and put it back in and everything starts all over again. Full message, even though the container is empty.

What strikes me is that after the pusher for the coffee grounds has moved over the cylinder, there is no clicking noise. My first assumption was a mechanical problem, but I can't see anything visually (machine disassembled).
When trying to reset according to the instructions, everything works up to point 10, namely that the piston does not stop in the lowest position, but in the highest position. From point 12, when I plug the plug back in, the reset process is not completed, but the machine is stuck again in the cycle described at the beginning.

Does anyone have any idea why this could be?

Great !!! Everything is running normally again. Many thanks for this advice.

Good evening,
Krups EA815070/70P
Coffee grounds indicator flashes after each coffee,

I've been through all your posts, very interesting, but I have a different fault to your findings,
I've tried to apply the factory reset but I can't get to step P2, I'm stuck just before.
The Marc tray presence sensor is ok, tested with a multimeter
I have to remove and replace the coffee grounds tray for each coffee ( sometimes it crashes afterwards, erratic )

If I don't find the soft tip, I'm thinking of simply replacing the motherboard
GSM0300143 (24€)

If this has already happened to you (?), do you have any ideas?
I doubt it's a component or organ, I think the motherboard counts the cycles and requires an oil change every X

Thank you
Jean louis

QUOTE (jlboix @ Sunday, September 22, 2024, 6:47 PM)

Good evening, Krups EA815070/70P Coffee grounds indicator flashes after every coffee, I have gone through all your posts, very interesting, but I have a different error from your findings, I have tried to apply the factory reset but I can't get to Step P2, I'm stuck just before it. The grounds container presence sensor is fine, tested with a multimeter I have to remove and reinsert the grounds container for each coffee (sometimes it crashes afterwards, erratic) If I can't find the soft tip, I'll just consider replacing the main board GSM0300143 (24€) If this has happened to you before (?), do you have any ideas? I doubt it's a component or an organ, I think the motherboard is counting cycles and asking for all X Thank you Jean louis

I guess a new motherboard would fix your issue.

QUOTE (Gast_HaWe @ Saturday, November 28, 2020, 4:22 pm)

KRUPS EA81* Reset with or without cleaning slide. Pomace container and water container LED flashing. Trying to change the grinder setting, grinder grinding time, grinding quantity, coffee powder quantity according to a procedure described in the forums usually makes the machine unusable. The grounds container and water container LEDs flash after restarting, no more button input possible, machine does not heat up. In a forum, an unknown forum user has described a possible RESET for all those affected. I expressly emphasize that I am not the inventor of this procedure, the credit goes to an unknown person. I am merely transferring the procedure into a readable form and adding a few more steps. I have tried it on a machine WITHOUT a cleaning slide. It works! 1. Disconnect the machine from the power supply (unplug) 2. Remove the water tank, grounds container and cleaning slide (if present) 3. Set the flow regulator to 20 ml 4. Press and hold the "strong coffee" button on the far right and plug in 5. All LEDs light up, water tank filled, grounds container, reset cleaning slide (if present) 6. Adjust the flow regulator until all LEDs have gone out (approximately middle position) 7. Place the container under the coffee spout and steam nozzle, now press the "weak coffee" button 8. Water is pumped through the coffee spout and steam nozzle, the brewing piston moves to the upper edge of the brewing chamber. The process is repeated twice. Then all red LEDs have gone out 9. Press the "weak coffee" button again 10. The machine lowers the brewing piston twice, the last time the brewing piston remains in its lowest position. When "all LEDs are flashing" 11. Unplug the machine and wait at least 5 seconds 12. Plug in the mains plug, the brewing piston returns to its original position. Machine is working again.

Worked great, but unfortunately the grinder did not reset itself and the pomace is still thin.
Are there any other instructions?

Thank you very much

--------------------
Jura S 90 und 95, Siemens S 60, Saeco Cappuccino Ring und immer wieder auf der Suche nach einer Anderen.

QUOTE (Guest @ Wednesday, December 15, 2021, 00:53)

I have the problem that my Krups EA 810870 only flashes blue after switching on and does not seem to heat up. If I press the power button again, it beeps twice and all red LEDs light up like KITT from Knight Rider (from left to right and vice versa). No button can be pressed either. I can't switch it off either, only unplug it. I have now tried the RESET, but during the reset, water only comes out of the steam nozzle, but not from the outlet. When I switch the machine on again after the reset, I have the same problem as before the reset.

Hello, have you found the problem, the same problem happens with my Krups?

QUOTE (error @ Wednesday, 09. October 2024, 14h35)

QUOTE (jlboix @ Sonntag, 22. September 2024, 18:47 Uhr) Good evening, Krups EA815070/70P Coffee grounds indicator flashing after each coffee, I've been through all your posts, very interesting, but I have another fault than your findings, I've tried to apply the factory reset, but I can't get to step P2, I'm stuck just before. The grounds container presence sensor is in good condition, tested with a multimeter I have to remove and replace the grounds container for each coffee (sometimes it crashes afterwards, erratic) If I can't find the soft tip, I'm just considering replacing the motherboard GSM0300143 (24€) If this has already happened to you (?), do you have any ideas? I doubt it's a component or an organ, I think the motherboard counts cycles and asks for all X Thank you Jean louis I think a new motherboard would solve your problem.

BINGO,
I was fed up with going round in circles,
I bought a motherboard 15 days ago, (24 euros)
I changed the motherboard this morning,
no more pb,
(no need to do any manipulations or resets or any other Chinese stuff, plug and play, simple)
for the old one, I'm keeping it, the day I get it, I'll be able to use it again.I'll keep it, the day I'll have the trick to put it back to factory config or if I know how to target the CMS in question,
go, have a good Sunday and a good coffee.
Jean Louis

QUOTE (Wilfrid @ Wednesday, 20. July 2022, 10:16 10)

There is no flow setting on the EA81* machine, no strong coffee button, no weak coffee button.... This procedure is not possible on this machine</br>

There are these buttons. But whether the described procedure works, I will check at home in the evening :-)

Hello,

My KRUPS EA815070 kept indicating that the coffee grounds compartment needed emptying, even though it had been emptied several times.
I carried out the 2 reset processes (the one starting with the "navigation" button, which invariably ended with P3) and then the one starting with the "maintenance" button, and since then it starts up but remains blocked. What's more, when you want to switch it off, it remains indefinitely in OFF mode without ever switching off completely (unless you unplug it).
Believing it to be a mechanical problem, I dismantled the entire upper part of the machine, cleaned up the coffee dust, changed the seals, re-greased the slides, etc., and above all checked the various micro-switches.
No further results.
What do you think? Electronic board out of order?
Thanks

QUOTE (Wilfrid @ Wednesday, July 20, 2022, 10:16 am)

With the EA81* coffee machine there is no quantity setting, no button for strong coffee, weak coffee... This procedure is not practical for this machine</br>

I have the same machine you have to go into the menu and there it says how strong the coffee should be